RGBlink
← Back to Support Hub
proAV

Support For Integrators & Commercial Installations

What we can help with

processor control, video routing, installation design, integration issues, and OpenAPI questions for proAV devices.

  • Commercial installations, processors, switchers, scalers, and distribution systems
  • OpenAPI control questions for proAV devices
  • System integration, deployment, and troubleshooting across installed projects

Start a support chat

Tell us your device model and what you need help with, or try a suggested question.

Support Knowledge

Select an article from the menu to view full content here.

General / mini Series / mini-pro v3 - Remote Control

Remote Control - mini-pro v3

Overview

mini-pro v3 introduces and updates the method of remote control for mini-pro to be via a browser based webApp. This provides for rich web based remote control from most laptop and mobule devices without the need for specialist software installation. The webApp simply runs in the browser.

Prior models

Prior models and editions (mini v1, mini v2, mini+ mini-pro v1, mini-pro v2) required the installation of the XPOSE mini desktop app and/or mobile app. No webApp is available for prior models.

Applies to

mini-pro v3

Requirements

  • Firmware: minimum v1.5
  • Laptop: a laptop with browser (Chrome/Edge) or mobile device with browser (Chrome/Edge/Safari). The laptop/mobile must be on the same network subnet as the device.

Configuration

Settings

  • Get the IP address of the mini-pro by pressing the "M" button on the front panel, tapping SETTINGS and entering the IP SETTING menu. In most environments the IP address will be "192.169.0.xxx"
  • Open a browser tab on a laptop (that is connected to the same network/LAN and enter the IP address of the mini-pro from above).
  • The webApp for mini-pro will be loaded into the browser with the PGM/program output shown.

If the RGBlink webApp does not open in the browser, check the Network settings of the laptop to ensure that both mini-pro and the laptop are on the same network subnet.

Operation

The following features are available from the webApp

  • MENU

  • Transition EFFECT selection

  • Enable PIP and select from a preset layouts

  • Enable and configre DSK Chroma Key features

  • Load/Recall available VIEWS

  • Open the OUTPUT menu

    • Set Main Output as PGM (live Program output) or to be a TP (Test Pattern).
    • Set the output Resolution and frame rate
    • Enable streaming with Push Flow settings
    • paste in StreamURL (with StreamKey) , press the Distribute button to save the settings to the device.
    • Turn on the ON AIR toggle to start live streaming.

  • Set up to Record

    • Start/Stop Recording to a connected to a USB drive/disk
    • Set Bitrate

  • Review SETTINGS

    • Fans: setting
    • Language switch between Chinese and English languages.
    • Input (no setting for mini-pro)
    • IP network/LAN settings
    • About information for the device

  • VIEWS - direct button to open the Load/Recall VIEWS

  • PROGRAM - Expands the Display the Program in full screen (hides the menu at right).

  • TBAR Tbar to switch between PST and PGM

    • Use the black/green buttons either side of the t-bar for CUT
    • Drag the Tbar for crossfade style transitions

  • LAYER A enables direct switching of the source signal for layer A

  • LAYER B enables direct switching of the source signal for layer

  • LOGO settingss

    • Turn on/off Show LOGO / Hide LOGO
    • install LOGO and XY postion

  • PTZ configuration and operation

    • IP - Manually enter or search for PTZ camera
      • Port - Set a custom VISCA port number (default is 1259)
    • Zoom
    • Speed
    • Auto Focus
    • Focus
    • Pan & Tilt
      • Reset position

  • AUDIO

    • Input - set audio mode and level for each input channel.
    • Output - set the output volume
    • Mic set the input gain level for the mini-jack

Reference

Guide: https://youtu.be/SUOgzMZ3CNA